I don't have pictures yet but should by tomorrow. With small adjustments on both sides you should obtain an even tick. Nearly all the clocks used in England were made abroad or by foreign European settlers. I am a horologist and have been working with clocks and watches for over 30 years. I found this little fellow in a box of bits this morning.
Gongs however, were not used in 1790 and were generally not in use until much later in the 19th century, a late Victorian preference. This is a period antique longcase clock was Robert Davey was recorded working in Norwich from 1751 to 1811 he was born in 1733, this clock dates to around 1800. The story is told by what you see, or don't see! Towards the end of the 18th-century, it then became all the more fashionable to produce a slightly smaller clock with a light-coloured dial. The mahogany clock case is of a good quality superb model. Brass Dials If your grandfather clock has a brass dial, it was probably made in the period between 1680 and 1770, and most likely between 1700 and 1770.
All of my clocks are working unless otherwise stated, I don't however regulate the clocks before listing - I leave that to you as every environment is unique. If you cast your mind back a few months, you posted a pic of one, when I said my memory was vague on the subject. There are occasional exceptions of course, some makers seemed to have a favorite feature which they kept using long after everybody else had moved on - - - Date and seconds subsidiary dials are usual now, and the small ornate hands fitted to these are also brass and matching. The change seems to have been made some time ago! Then, they were silvered over and engraved. This clock is a Yorkshire clock case with fine carvings to the case. Prior is recorded as often buying his movements. .
Restoration included comprehensive cleaning and removing rust. Clocks of this nature were regularly used in large galleries or turrets. The same holds true on the spring clocks. I think it was you posted a shot of one the same as the original post. Careful scrutiny of the case shows that new cheeks have been glued into the case to achieve a near perfect fit, figure 15. These latest features now suggest that the dial was not made for this clock, and is probably 70 to 80 years older than the movement and case. Looking at a few 30 hour movements I had buried, the bell stands vary front, back , inside, outside, through the bridge and outside the bridge.
And it was certainly widely used in banjo clocks, mirror clocks, coffin clocks, bracket clocks, wall clocks, and a wide range of shelf clocks, of the same periods. Below is a photograph of a Birmingham plate or a false plate. The late ones 1800 to 1880 have a wide flat strip of iron instead of the wire rod, and the same four inch brass-faced bob. The missing numbers were often replaced with little symbols, often looking like stars. Very popular outside London 1700 to 1725 Can be seen on the early brass dial pictured above.
You may need some assistance if you are on your own at this point. We also have a good selection of antique country furniture from both England and France with some more extravagant walnut pieces from the Low Countries. This feature started to appear C1760, and continued afterwards on good quality work. Doesn't really make good sense. Re-assemble the whole clock when you are happy with the wall fixing and then swing the pendulum. If the tick is uneven the clock will usually stop. But there's a pic of a rare printed label from 1691 of setting up instructions original to a longcase clock by Joseph Windmills in Neale's book on him.
This chapter ring has half-hour markers; these had all but disappeared by 1780, and usually before 1760. I said, I thought I had seen that before, but couldn't remember, and posted a picture of an old spare back plate I had, which had the clean mark showing where the bell stand had been. A large spandrel, mainly used in Northern England C 1750 to 1775 6. Brass dials tended to simplify again from C. Decoration consisted of spandrels painted on in gold paint in the four corners, probably to resemble the cast brass spandrels fitted to brass dials. The weights are brass cased and lead filled. I am a horologist and have been working with clocks and watches for over 30 years.
He had a problem with a feature of a Parisian religious building. We can also be reasonably confident that the clockmaker and cabinetmaker, who made the case, were not the same. Since many of the 30 hour clocks were provincial, with clockmaker's doing their own thing, guild free, it's not surprising. The later Southern clocks usually have a dial which is a single sheet of thin brass, silvered all over and resembling an early painted dial at first glance. All of my clocks are working unless otherwise stated, I don't however regulate the clocks before listing - I leave that to you as every environment is unique. We have been established since 1978, dealing in and restoring most antiques, specialising in clocks.
If you are screwing the case to the wall you will need to remove the whole clock but obviously in reverse order to the process above. Eventually most clocks went back to a plain or matted centre again. Below, you can see another French movement prior to and after its restoration. I have to return with a good camera and disassemble and take photos 2019, National Association of Watch and Clock Collectors, Inc. D: 1700 to 1715 in London, around 1730 to 1740 in the provinces. Very typical of the late dials, except for the center seconds and use of minute numbers. To maintain or restore the value of a clock we always stress to seek the help of an experienced restorer.