The instructions apply to replacing an existing water line, as well. I would like to attach it to the water line directly. Wrap a small amount of pipe thread tape around the water supply line fitting on the back of the water valve. Take the flexible water-supply tubing from the back of the refrigerator and feed it down through the hole in the floor. A good replacement for this line is a stainless steel line.
An Adapt-a-Tee is an ideal plumbing fitting for this purpose. Residents of the Pittsburgh area can contact , day or night. Protects your refrigerator, drinking water, and ice maker from sediment and chlorine taste and odor. All other brands, products and services, and their respective trademarks, names and logos, are the property of their respective owners. Connecting to a Kitchen Supply Line Keep in mind that if you are going to be installing the water line onto the kitchen water supply, make sure the line sits before the shut-off valve, so that you will not shut the water off to the fridge when working on the sink. Once the door or doors are removed, the refrigerator will be much thinner and easier to move into the kitchen.
Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher. Tighten it by hand, then turn it one-quarter turn with an adjustable wrench. The choice is yours, but the copper tubing typically lasts longer. Once the filter was installed, the water was drinkable. Repeat this process for the connection on the refrigerator. Then flush and drain the tank. Once the nut is hand tight, a half turn with a wrench or pliers should do the trick! A newly-installed water filter cartridge may cause water to briefly spurt from the dispenser.
If the fitting leaks, tighten the compression nut and check again. Designed to fit major brands of refrigerators and icemakers. This will keep the line from pulling out of the nuts at the valves, and make it easier to move the refrigerator out from the wall in the future. Follow these simple steps, and your next plumbing job will be much easier. If you are using 08 Plastic Tubing A , insert the 06 Molded End Bulb of the 08 Plastic Tubing A into the compression fitting. Use an adjustable wrench to tighten the nut onto the refrigerator. This line could be one from the basement, the kitchen sink, or elsewhere.
This will puncture the water pipe. Open the water supply cut-off valve. Try tapping the floor to find the hollow sound between the floor joists for a good place to drill a hole. Measure the distance carefully, and buy a supply tube with plenty of length for the job. Tape the end of the tubing and push enough tubing through the hole to make a couple of large loops. If you are interested in how refrigerators work, read my article on.
Many home improvement and hardware stores offer kits made of copper tubing, or flexible braided or plastic piping. Turn on the saddle-tee valve and check for leaks. If you have a basement, tap into the cold water pipe down there. Cut into the cold-water line using a tubing cutter. Which is what I love. If there are leaks, tighten the nuts on the valves a half turn at a time with a wrench or pliers until the leaking stops. Connect the compression nut to the saddle valve.
You must pull the refrigerator away from the wall to access water line connections on it. Sweep out the space to get rid of dust and dirt, then connect the power and water, making sure that the cables for both are against the wall so they won't get caught as the refrigerator slides in. Select the location for the valve on your water line. This gives easy-to-follow instructions for replacing the water inlet valve on a refrigerator. Turn the water supply valve on and check for leaks. Tighten the fittings as needed, using channel-type pliers or an adjustable wrench.
If possible, drill the hole from the top down to ensure correct placement. The saddle valve is two pieces of metal strapped on a pipe. They should run parallel and be fairly close together. Then, connect the water line to it. You might see some leakage here because the valves are usually not turned off and on unless repairing or replacing the faucet. Step 1 — Drill an Access Hole for the Line Check the basement directly underneath the refrigerator for an available cold water supply line and determine where the hole must be drilled for the water line. Designed to fit major brands of refrigerators and icemakers.
Then, tighten the screws to secure the valve to the pipe. As for it being a 5 year filter that make. Using any other type of cold water supply line could cause odd or off tasting ice. If not, you will need to run a line to the nearest cold water pipe, which is probably in the floor below your kitchen. For this feature, you need to run a water supply line to the back of the fridge. Ensure the water supply line is installed correctly and the correct tubing was use.