Step 2 — Remove the Old Lines Using the proper size open-end wrench, remove the supply line from the valve. I purchased a new refrigerator and need to install a water line to the ice maker. Use a spade bit to drill up through the flooring. However, I thought I'd check here first. Your feedback makes this site better for all users. Next, locate a place on the main trunk supply line where you can tap the saddle valve. Get an actual T fitting put on whether it be you or a plumber.
Keep in mind, the kitchen sink may not be the closest source of cold water. Refrigerator icemakers use a valve that opens and closes very quickly. To estimate costs for your project: 1. But once you've bought a refrigerator with a cold water dispenser and automatic ice maker, you'll still need a way to get water into it. The dispenser pressure is still disappointing compared to other people's fridges I've used but it does fill a cup in under a minute now. Press the plastic sleeve into the end of plastic tubing. This method uses job specific detail for superior pricing accuracy and transparency - and has become an industry standard through publications and guidance of leading trade associations, including: , the , the , the , and the.
If the line is just a replacement, Follow all of the same steps with the exception of drilling the hole in the cabinet and adding the valve, then screw the nut with the line on the existing valve. Set Project Zip Code Enter the Zip Code for the location where labor is hired and materials purchased. If you imagine other water supply sources easier to connect to your fridge, it may be from an upstairs bathroom, a washing machine located in the basement or upstairs, or even the water supply line to your water heater. Step 3 — Connect the Water Line to the Refrigerator Next, wrap the threads on the water-line connector that is on the back of the fridge with to lubricate the threads. The associate from that department would be happy to help you choose the best option for your situation. It would be easy to add a coupler to tap into the existing line but doing so adds an extra place for a leak to occur. Then turn the handle on the valve counter-clockwise to pierce the line.
If in doubt, hire it out. I am not putting down Sharkbite and in fact recommended it as an alternative to crimping in my first post. After installing the water line, flush the water line and filter by pressing and holding down the water dispenser lever with a container to catch dispensed water. Turn off the water and then let your sink run to drain what is left in the pipes. Remove the line from tank. Where I live, they were still using galvanized pipe back then.
Check the connections and, if necessary, tighten. Turn off water at supply stop. I was able to locate the nearest water line, which comes from my outdoor faucet that is inside a wall right next to the refrigerator. Install Saddle Valve, to the supply line pipe in basement to tap into water for the refrigerator. I am a total novice at plumbing. Most plumbers recommend that you don't use the self-piercing style. The cold water line is pretty much right below the refrigerator in the basement so I can easily drill a hole behind the refrigerator to the basement.
These reverse osmosis systems are usually plumbed in with plastic tubing as well so in order to splice into the line, you only need to cut the tubing with either a pair of tubing cutters or you can use you side cutters. Attach the compression nut to the wall supply valve. If I install a water line for the refrigerator, turning this valve off in the winter will also turn the water supply to the refrigerator off as well. No need to run super heated water to the fridge. To Tap Water Supply 1. Install an olive compression sleeve and compression nut to the other end of the line, and attach this to the input of the refrigerator.
Make sure to install an in-line filter for the ice maker to avoid problems with the refrigerator. Comments must be on-topic, helpful, and kind. For this feature, you need to run a water supply line to the back of the fridge. If you use a vampire tap, and you have to replace the tap, you'll have to shut off the water for the whole house. Connect the compression nut to the saddle valve. Test the water pressure by dispensing water into a measuring cup for 10 seconds.
A picture or a drawing of the layout might help. They clamp on to an existing water line and have a sharp pin inside. Then, drill a hole through the side of a cabinet or through the floor to thread the line through, depending on where your supply line is located. These instructions will not mention the saddle valve, but if you are wanting to use one because of ease, no problem. Try tapping the floor to find the hollow sound between the floor joists for a good place to drill a hole.
I have a newish refrigerator that has a water supply for ice, cold water, etc. Connect tubing to saddle valve. I want to install a water line for an icemaker refrigerator I'm about to purchase. It will only self tap into copper. If there are leaks, tighten the nuts on the valves a half turn at a time with a wrench or pliers until the leaking stops.
What do I need here, another shutoff valve at the refrigerator? Here are the instructions for the Watts ice maker kit model K-1. Water-line breaks can also develop from movement or accidental bumping of the pipes, which naturally can occur with normal refrigeration use. The location of your tap will determine how many holes you have to drill to feed the water line through. I always joke with him that it is perfect for whenever I want hot chocolate. This will allow you to shut the water off only to the fridge in case of leaks, repair or simply replacing the fridge itself.